How do I replace the serpentine belt on a Chrysler Town and Country?

Release tension on the automatic tensioner with a breaker bar, slide the old belt off, route the new belt per the diagram (usually on a sticker under the hood), and release the tensioner onto the new belt. The job takes 15-30 minutes.

How do I know if my Chrysler Town and Country serpentine belt needs replacing?

Signs include squealing at startup, visible cracks or fraying on the belt, loss of power steering or A/C, and the battery light coming on. Most belts should be replaced every 60,000-100,000 miles.

What happens if the serpentine belt breaks on my Chrysler Town and Country?

If the serpentine belt breaks, you lose power steering, alternator charging, A/C, and (on some engines) the water pump. Pull over immediately — driving without the water pump will cause overheating and engine damage.

Where is the belt routing diagram on a Chrysler Town and Country?

Most Chrysler Town and Country models have a belt routing diagram on a sticker under the hood, near the radiator support or on the inner fender. If it's missing, check the service manual or see the diagrams below.

⚙️Serpentine Belt

Chrysler Town and Country Serpentine Belt

Find serpentine belt routing diagrams, part numbers, and replacement instructions for your Chrysler Town and Country. All years covered.

Quick Answer

The Chrysler Town and Country serpentine belt routes around the alternator, power steering pump, A/C compressor, and water pump. Belt length and routing vary by engine — see diagrams below.

2011-2016

Belt TypeMulti-rib serpentine (6PK or 7PK)

Belt Length85" - 100" (varies by engine and A/C option)

Tensioner TypeAutomatic spring-loaded tensioner

Replacement Interval60,000 - 100,000 miles

Notes

→Take a photo of the belt routing BEFORE removing the old belt
→Use a 1/2" breaker bar or 15mm socket to release the automatic tensioner
→Inspect the tensioner pulley and idler pulleys for bearing noise while the belt is off
→A new belt may squeal briefly at startup — this usually stops within a few minutes

Shop on Amazon →Full Repair Guide →

2005-2010

Belt TypeMulti-rib serpentine (6PK or 7PK)

Belt Length85" - 100" (varies by engine and A/C option)

Tensioner TypeAutomatic spring-loaded tensioner

Replacement Interval60,000 - 100,000 miles

Notes

→Take a photo of the belt routing BEFORE removing the old belt
→Use a 1/2" breaker bar or 15mm socket to release the automatic tensioner
→Inspect the tensioner pulley and idler pulleys for bearing noise while the belt is off
→A new belt may squeal briefly at startup — this usually stops within a few minutes

Shop on Amazon →Full Repair Guide →

1999-2004

Belt TypeMulti-rib serpentine (6PK or 7PK)

Belt Length85" - 100" (varies by engine and A/C option)

Tensioner TypeManual adjustment bolt or automatic

Replacement Interval60,000 - 100,000 miles

Notes

→Take a photo of the belt routing BEFORE removing the old belt
→Check if your model uses automatic or manual tensioner adjustment
→Inspect the tensioner pulley and idler pulleys for bearing noise while the belt is off
→A new belt may squeal briefly at startup — this usually stops within a few minutes

Shop on Amazon →Full Repair Guide →

1993-1998

Belt TypeMulti-rib serpentine (6PK or 7PK)

Belt Length85" - 100" (varies by engine and A/C option)

Tensioner TypeManual adjustment bolt or automatic

Replacement Interval60,000 - 100,000 miles

Notes

→Take a photo of the belt routing BEFORE removing the old belt
→Check if your model uses automatic or manual tensioner adjustment
→Inspect the tensioner pulley and idler pulleys for bearing noise while the belt is off
→A new belt may squeal briefly at startup — this usually stops within a few minutes

Shop on Amazon →Full Repair Guide →

1990-1992

Belt TypeMulti-rib serpentine (6PK or 7PK)

Belt Length85" - 100" (varies by engine and A/C option)

Tensioner TypeManual adjustment bolt or automatic

Replacement Interval60,000 - 100,000 miles

Notes

→Take a photo of the belt routing BEFORE removing the old belt
→Check if your model uses automatic or manual tensioner adjustment
→Inspect the tensioner pulley and idler pulleys for bearing noise while the belt is off
→A new belt may squeal briefly at startup — this usually stops within a few minutes

Shop on Amazon →Full Repair Guide →

Frequently Asked Questions

How do I replace the serpentine belt on a Chrysler Town and Country?: Release tension on the automatic tensioner with a breaker bar, slide the old belt off, route the new belt per the diagram (usually on a sticker under the hood), and release the tensioner onto the new belt. The job takes 15-30 minutes.
How do I know if my Chrysler Town and Country serpentine belt needs replacing?: Signs include squealing at startup, visible cracks or fraying on the belt, loss of power steering or A/C, and the battery light coming on. Most belts should be replaced every 60,000-100,000 miles.
What happens if the serpentine belt breaks on my Chrysler Town and Country?: If the serpentine belt breaks, you lose power steering, alternator charging, A/C, and (on some engines) the water pump. Pull over immediately — driving without the water pump will cause overheating and engine damage.
Where is the belt routing diagram on a Chrysler Town and Country?: Most Chrysler Town and Country models have a belt routing diagram on a sticker under the hood, near the radiator support or on the inner fender. If it's missing, check the service manual or see the diagrams below.

More Chrysler Town and Country Guides

🛢️Chrysler Town and Country Oil Type & Capacity 🔋Chrysler Town and Country Battery Location 🔘Chrysler Town and Country Tire Size ⚙️Toyota Camry Serpentine Belt ⚙️Toyota Corolla Serpentine Belt ⚙️Toyota RAV4 Serpentine Belt ⚙️Toyota Highlander Serpentine Belt ⚙️Toyota Tacoma Serpentine Belt ⚙️Toyota Tundra Serpentine Belt

Need a full step-by-step repair guide?

Start Free AI Diagnosis →

100% Free — No signup required